Hartzell PJ, Glennie CL, Finnegan DC (2013) Calibration of a terrestrial full waveform laser scanner. Goodman RE (1989) Introduction to rock mechanics, 2nd edn. Gigli G, Casagli N (2011) Semi-automatic extraction of rock mass structural data from high resolution LIDAR point clouds. Eng Geol 183:290–302įrancioni M, Salvini R, Stead D, Giovannini R, Riccucci S, Vanneschi C, Gullì D (2015) An integrated remote sensing-GIS approach for the analysis of an open pit in the Carrara marble district, Italy: slope stability assessment through kinematic and numerical methods. Dissertation, University of Sienaįrancioni M, Salvini R, Stead D, Litrico S (2014) A case study integrating remote sensing and distinct element analysis to quarry slope stability assessment in the Monte Altissimo area, Italy. Sperimentazione di differenti software per l’estrazione semi-automatica dei dati di giacitura. Tunn Undergr Space Technol 25:614–628įorzini C (2014) Analisi della fratturazione nei versanti in roccia a partire da dati laser scanner terrestre. Landslides 10(4):409–420įekete S, Diederichs M, Lato M (2010) Geotechnical and operational applications for 3-dimensional laser scanning in drill and blast tunnels. Int J Rock Mech Min 66:41–48įanti R, Gigli G, Lombardi L, Tapete D, Canuti P (2013) Terrestrial laser scanning for rockfall stability analysis in the cultural heritage site of Pitigliano (Italy). Technical Report AFNL-TR-65-116, National Technical Information Service, Air Force Weapons Laboratory, New Mexico, pp 300ĭeliormanli AH, Maerz NH, Otoo J (2014) Using terrestrial 3D laser scanning and optical methods to determine orientations of discontinuities at a granite quarry. SELCA, Firenzeĭeere DUR, Miller P (1966) Engineering classification and index properties for intact rock. Geoitalia 21:19–30Ĭoli M, Grandini G, Matteini L (1987) Carta Strutturale del bacino marmifero di Orto di Donna (Alpi Apuane), 1:5000. Mem Soc Geol Italiana 49:99–124Ĭarmignani L, Conti P, Fantozzi PL, Mancini S, Massa G, Molli G, Vaselli L (2007) I marmi delle Alpi Apuane. J Geol Soc 165(3):625–638Ĭarmignani L, Fantozzi PL, Giglia G, Meccheri M (1993) Pieghe associate alla distensione duttile del complesso metamorfico apuano. Chapman & Hall, London, p 571īuckley S, Howell J, Enge H, Kurz T (2008) Terrestrial laser scanning in geology: data acquisition, processing and accuracy considerations. Wiley, New York, p 272īrady BHC, Brown ET (1994) Rock mechanics for underground mining. Alex Eng J 50:399–405īieniawski ZT (1989) Engineering rock mass classifications. J Sediment Res 75(2):166–176īeshr AAA, Elnaga IMA (2011) Investigating the accuracy of digital levels and reflectorless total stations for purposes of geodetic engineering. Eng Geol 7:287–332īellian JA, Kerans C, Jennette DC (2005) Digital outcrop models: applications of terrestrial scanning lidar technology in stratigraphic modeling. J Struct Geol 66:102–114īarton NR (1973) Review of a new shear strength criterion for rock joints. Earth Surf Proc Land 39:80–97Īssali P, Grussenmeyer P, Villemin T, Pollet N (2014) Surveying and modeling of rock discontinuities by terrestrial laser scanning and photogrammetry: semi-automatic approaches for linear outcrop inspection. Data were grouped, analysed, and shared in a single repository for VR visualization and stability analysis in order to study the interaction between geology and human activities.Ībellàn A, Oppikofer T, Jaboyedoff M, Rosser NJ, Lim M, Lato MJ (2014) Terrestrial laser scanning of rock slope instabilities. joint roughness, alteration, opening, moisture, and infill) were also included in the VR models. Some fundamental geotechnical indices (e.g. The quality of data collected through geomatic surveys and field measurements in two marble quarries of the Apuan Alps (Italy) was very satisfactory. Discontinuities were compared with data from traditional engineering-geological surveys in order to check the level of accuracy in terms of the attitude of individual joints and sets. Data from laser scanning and high quality images were combined to map deterministically and characterise discontinuities with the aim of creating accurate rock mass models. In this context, modern geomatic tools enable the remote acquisition of information that can be used to produce georeferenced high-definition 3D models: these can be used to create a VR in support of rock mass data processing, analysis, and interpretation. VR uses a computer to produce a simulated three-dimensional world in which it is possible to interact with objects and derive metric and thematic data. The latest technological developments in computer vision allow the creation of georeferenced, non-immersive desktop virtual reality (VR) environments.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |